CAN I SET UP A BATHTUB MYSELF?

Can I Set Up A Bathtub Myself?

Can I Set Up A Bathtub Myself?

Blog Article

Free Estimate

The content following next relating to How to Install a Bathtub is immensely remarkable. Give it a try and draw your own personal findings.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Installing a bathtub isn't exactly rocket science, but it does call for strong plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bath tub with a brand-new one is additionally a reasonably tough job. If the old tub is readily accessible, the project can relocate easily; if you need to open up a wall to remove the old tub and also place the brand-new tub, the task is a lot harder. In either instance, the job is within a house handyman's skills, although you will need a helper to move out the old tub and embeded in the brand-new one. Make certain you have actually qualified yourself for the job and fit trying it. As opposed to employing a specialist to take over a halfway-completed job, it is better to consider using one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This write-up will certainly assist you install a new bath tub in your shower room if you have already acquired a brand-new tub and do not need to change the plan of your previous water system pipelines.
Your tools and product checklist need to make up the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipeline Caps


  • Removing Old Taps


    If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water supply. After doing so, switch on the faucets to drain any kind of water staying in the system. The process of eliminating the existing faucets can be rather bothersome because of the limited gain access to that is usually the situation.
    Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have actually been gotten rid of, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
    Prior to going on to fit the new faucets, contrast the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.

    Fitting New Taps


    If the tails of the new faucets are plastic, after that you will need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipes.
    If you need to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
    Next, position the tap in the installing opening in the bath/basin making certain that the washing machines are in place between the faucet and also the sink. Safeguard the tap in place with the producer offered backnut. When the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The previous kind needs to be connected to the tap ends first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been linked.

    Setting up the Tub


    Utilizing both wood boards under its feet, put the tub in the needed setting. The wood boards are practical in equally spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 little points.
    The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the spirit level and also readjusting the feet on the bath tub till the level checks out degree.
    To set up taps, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the same for the other faucet.
    Turn on the water system as well as inspect all joints and brand-new pipework for leakages and also tighten them if required. Load the tub as well as likewise examine the overflow electrical outlet as well as the typical outlet for leaks.
    Finally, fix the bathroom paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bathtub should wait until the bath tub has actually been utilized a minimum of once as this will settle it right into its last setting.

    Getting ready for the Installation


    Firstly, the sustaining structure provided with the bath should be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets unit to stop pressure on the bath tub.
    Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you utilize all of the supplied washing machines.
    Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should now be ready to be suited its last position.

    Tiling Around the Bath tub


    In the location where the bath fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to crack an inflexible seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, resulting in difficulties with moisture and possible leakages to the ceiling below.
    You can pick from a range of coloured sealers to blend in your components and installations. They are sold in tubes as well as cartridges, and also are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to permit the motion experienced when the bathtub is in use. The sealer can crack relatively very early if you do not consider this activity prior to sealing.
    Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently available on the marketplace. It is suggested to fit the tiles utilizing waterproof or waterproof adhesive as well as cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    We had been guided to that editorial about How to Install a Bathtub Yourself through an associate on a different web page. Do you know about someone else who is looking into the subject? Do not hesitate to promote it. Many thanks for your time. Come back soon.




    Schedule Now


    Report this page